Electrolux Washer Leaking Water? Here's How To Fix It (2024)

Washing machines like those made by Electrolux have surged in popularity in recent years due to theirmodern appliances, superior efficiency, and sleek low-profile design.

Homeowners love being able to toss a wholeloadof dirty clothes into these large-capacity washers to save time on laundry day. However, as convenient as they seem, these machines also come with a common downside – messywasher leaks.

It’s not unusual to discover puddles of sudsy water on the floor under your Electrolux washing machine. Awater leakcan not only cause stains and damage nearby walls and flooring, it’s also an indicator that your washer needs some repair or maintenance attention.

This comprehensive guide will provide you with expert troubleshooting advice to detect exactly where yourElectrolux washerisleakingfrom. You’ll also find clear directions outlining how to fix theleakyourself.

How To Fix Electrolux Washer Leaking From Bottom

If you notice water pooling underneath your Electrolux washing machine, chances are there’s an issue causingwater leakagefrom thebottom of the machine. Let’s explore the most likely culprits behind bottomleaksand the best ways to remedy them.

1. DamagedDrain Pump

A damageddrain pumpis one of themost common reasonsthat’ll make yourElectrolux washerleakfrom the base panel area.

The pump is responsible for draining water from thewash tubat the end of awash cycle. If the pump housing develops anysplits, cracks, or the internal bearings wear out,leakscan occur.

Replacing a damageddrain pumpis the most direct solution to resolvingleaks from this component. To replace a damaged drain pump follow the instructions outlined below:

Supplies Needed:

• Newdrain pumpcompatible with your Electrolux model
• Adjustable pliers
• Screwdriver set
• Bucket
• Rags

Steps Involved:

1. Unplug washing machine power cord from outlet to prevent electric shock.
2. Locate the access panel and remove screws with a screwdriver. Lift off the panel.
3. Spread rags underneath the washer near thedrain pumpto catchleaks.
4. Use pliers to detach thedrain hosefrom the pump outlet port. Allow water still in thehoseto drain into the bucket.
5. Disconnect wire harness plug from rear of pump.
6. Using screwdriver, loosen pump mounting screws. Remove screws once loose enough to slide the pump out.
7. Carefully extract the pump out of the washer cabinet, taking care not to damage surrounding parts.
8. Align replacement pump into position, insert mounting screws. Tighten screws with screwdriver.
9. Reconnect wire harness plug to pump electrical terminal.
10. Attachdrain hoseto outlet port on new pump. Ensureconnection pointsareleak-free.
11. Replace access panel, screw back into place. Plug the washer power cord back in.
12. Run a short testcycleand verify noleakscoming from the new installeddrain pump.

2. Too Much Detergent

Too much detergent in your washerloadscan also lead toleaksdown below.Excess of suds(ie., alot of foam) mayclogdrainage pathways and start backing water up until it seeps out thebottom of the washing machine.

Always measure your detergent carefully and use only HE formulations designed forfront load washers. Refer to your detergent container to verify you’re using the right amount based onloadsize for yourfront load washing machine.

3. TornTub Seal

On some occasions, a tear in thetubrubber sealallows water from the inner drum to escape into the cabinet underneath. And if something causes thedrain pumpto stop emptying properly, thetubmay startoverflowing.

For a leakytub seal, the repair is more complex. You essentially have to take apart thewasher tub, replace seal and bearings as a unit, then reassemble. Not a quick job but it solves the root issue. Here’s how to do it:

Supplies Needed:

• Tub seal& bearing replacement kit for model
• Screwdrivers
• Adjustable wrench set
• Gloves & bucket
• Wood blocks

Steps Involved:

1. Unplug the washer and turn off thewater inlet valve. Open thefront doorand pull out the detergent tray.
2. Pry off the top panel. Unscrew vibration dampener block. Detach allwater supply hoses/wiring connected to innertubassembly.
3. Tip the washer back carefully onto wood blocks. Unscrew front panel screws and remove panel.
4. Disconnect shock absorbers by removingtubmounting pins. Pull shocks offtubassembly.
5. Disconnectdrain pumphoses& wires. Dislodge pump from cabinet.
6. Unhook suspension springs, lift and lowertubassembly out onto floor while supporting weight.
7. With wrench unscrew outertubbolts, separating front and rear outertubhalves.
8. Use a screwdriver to pry out the oldtub sealfrom the reartubgroove. Apply liquid soap to the groove.
9. Press in the newtub sealfrom the replacement kit using a screwdriver until fully seated.
10. Rejoin outertubhalves, replace bolts using wrench.
11. Lifttubassembly back into washer cabinet, reconnecting suspension springs & components.
12. Reattach allhoses, wires, panels in reverse order of disassembly.
13. Restorewater supply& power. Run a short testcycleto verify fixedleak.
14. Note: If the pump merely malfunctions, installing a brand-new drain pump restores normal drainage to prevent overflow leaks from below.

How To Fix Electrolux Washer Leaking From Back

If you notice water pooling on the floor behind yourElectrolux washer, theleaklikely stems from loose connections or damagedhoses(includingtub-to-pump hoseandfill hose) at the rear. Now let’s take a more detailed look at thepotential causesof backleaksand their solutions.

1. Damaged or Disconnected Water Inlet orDrain Hose

Thehosesconnected to the back of your washing machine can sometimes springleaks. Check the hot andcold waterhosesas well as thedrain hosefor cracks, holes, or loose connections.

If ahoseis damaged:

You will need:

• Newhoses
• Pliers
• Bucket

Steps:

1. Turn off the hot andcold watervalves behind the washer.
2. Unplug the oldhosesfrom the faucets. Use pliers if needed.
3. Unplug the oldhosesfrom the washer. Put a towel under to catch water.
4. Check the washer and faucet fittings for cracks. Replace washers if missing.
5. Attach the newhot waterhoseto thehot waterfaucet. Tighten by hand. Redhose=hot water.
6. Attach the other end of the hothoseto the washer. Tighten by hand.
7. Repeat steps 5-6 for thecold waterhose, using the bluehose.
8. Turn the water on fully. Check forleaks. Tighten with pliers ifleaks.
9. Run a testcycleto check forleaksbefore washing clothes.

2. LooseHose

Even inlet/drainhosesin good condition can spray water out if their fittings loosen up. This happens because the constant vibrations from the washcyclesmay cause connections to loosen slowly over time if not tightened properly.

For connections at supply lines or discharge pipe, hand tighten any fittings that show gaps using pliers. Don’t overtighten or you may strip threads. Ensure rubber sealing washers inside the female connections remain in place – If they are missing, replace them.

Provide some slack forhosesso they don’t rub and wear against the wall with machine vibrations. Periodically check clearance. And consider replacing olderhosesevery 5 years as preventative maintenance.

7 Most Common Electrolux Front Load Washer Problems

How to Fix Electrolux Washer Leaking From Door

Leaksstreaming out around the door perimeter as yourElectrolux washerruns can be incredibly frustrating to deal with. However, inspecting and addressingdoor sealissues promptly can eliminate the problem for good.

1. DamagedDoor Seal/Gasket

First check for any visible damage to the rubberdoor gasketthat frames the opening. Cracks, gouges, or holes along thedoor sealcompromise its ability to keep water safely contained within the drum.Residuebuildupleft unchecked can also affect the seal over time.

Start troubleshooting by running your finger carefully along the rubberdoor gasket, visually inspecting as well to check for cracking damage or holes allowing floodwater to escape. If there’s any defect after inspection, the seal needs to be replaced.

To replace a damaged seal, follow these set of instructions:

Supplies Needed:

• Replacementdoor sealfor your Electrolux model
• Gloves
• Needle-nose pliers
• Screwdriver

Steps Involved:

1. Unplug the washing machine from thepower source. Turn offwater supplyvalves.
2. Open the washer door and inspect the damageddoor seal. Identify type of seal attachment such as adhesive or plastic retainer.
3. Wearing gloves, use your hands or pliers to peel away damaged seals from door opening. Remove allresidue.
4. Thoroughly clean door perimeter seal seating area using appliance cleaner and lint-free rag.
5. Ensure the new seal shape matches the door opening. Align seal ends if multi-piece style and press adhesive strips firmly.
6. Starting at corners first, hand press the new seal into place around the entire door opening perimeter to adhere.
7. Using flat screwdriver, insert plastic seal retainer into designated slots around door perimeter, securing full seal attachment.
8. Inspect final seal placement by closing the door and checking for uniform contact and atight sealwith no gaps.
9. Plug in the machine power cord and turnwater supplyvalves back on after replacement.
10. Run a test emptycyclewhile observing forleaksto confirm fully fixeddoor sealreplacement before adding laundry.

2. Overloading

Another common source ofleaksstems from overloading the drum past recommended capacities. Items that get wedged between the seal and door result in water bypassing an otherwise intactgasket.

Be sure towipeclean thedoor sealwith weekly machine maintenance using warm,soapy waterand rags. This removes any lingering dirt, soap scum, orovergrowth of moldfrom impeding proper contact all the way around the opening perimeter.

Loading problems that frequently causeleaksrelate to overstuffing and unbalanced washing machine drums. Make sure to leave several inches of clearance around the inside and don’t exceed the maximum dryloadweight rating. This allows enough extra room for garments to float freely without catching along seal edges.

Electrolux Washer Error Codes E10, E11: How To Fix Them

Conclusion

As inconvenient asleakscan be with yourElectrolux washer, identifying theleakorwater source(i.e., theroot cause of the problem) accurately first makes repairing them much easier.

Start by inspectingdoor seal,clamp,inlet hose of the machine(i.e., including thedrain hose), pumps, andtub sealssystematically to pinpoint flaws allowing water to escape or overflow. Follow step-by-step instructions provided to properly replace damaged parts like torn door gaskets or cracked drainage pumps.

And remember preventative maintenance goes a long way – regularly wiping awayresiduebuildupand replacing worn out seals/hosesprevents manyleaks.